Linkskey LKV-S02ASK Bedienungsanleitung PDF herunterladen

Quick I nstallation G uide Applicable models: LKV-S02ASK /

LKV-S04ASK

User-definable Hotkey Preceding Sequence

Simultaneous /independent PC/Audio Switching

LKV-S02ASK/LKV-S04ASK

2/4-port Slim Palmtop PS/2 KVM Switch

with

Audio&Mic

Quick Installation Guide

Thank you for purchasing the

LKV-S02ASK/LKV-S04ASK

Slim Palmtop PS/2 KVM Switch with Audio&Mic! With

our highly reliable and quality product, user can enjoy countless

benefits from using it.

LKV-S02ASK (w/ Audio&Mic)

LKV-S04ASK (w/ Audio&Mic)

Introduction

The LKV-S02ASK/LKV-S04ASK is a 2/4-port Slim

Palmtop PS/2 KVM Switch with the

audio and microphone

switching function. It allows you to access, control, boot and

reboot multiple PS/2-enabled computers using only one keyboard,

video, mouse, and

one

speaker set and one microphone. It also

offers user-programmable simultaneous/independent

switching of

PC channel and Audio/Mic channel for flexible multimedia

application with KVM switching. For users who might need to

use a hotkey preceding sequence other than two scroll locks, we

also offer five key alternatives for free configuration.

Before you install

The default setting of the LKV-S02ASK/LKV-S04ASK is

appropriate for most systems. The KVM Switch is a Plug-and-

Play device for installation. In fact, you do not need to configure

the KVM Switch before installation.

For the first time installation of the KVM Switch, please follow the

instructions below for correct setup sequence:

The

correct setup sequence

is ……

(1) Connect the shared keyboard, monitor and mouse and

the speaker set and the microphone to the KVM Switch

first, and then connect your computers.

(2) Power up your connected computers…

Since the KVM Switch receives power from the computer’s PS/2 interface,

it is powered up when you connect the KVM Switch to a PC.

Out-of-the-box Installation

Take the KVM Switch out of th

e box and begin installation….

DO NOT TRY

to connect the KVM Switch to the computers while

the computers are still in powered-on states. Otherwise, the computer

will have difficulty recognizing yo

ur shared keyboard and mouse.

Step 1.

Make sure all the computers that are to be connected to

the KVM Switch and their peripherals are in powered-off

state. If not, power them off before you proceed with

the following steps.

Step 2.

Connect the shared PS/2 keyboard, mouse, monitor,

speaker set and microphone to the KVM switch.

Step 3. Connect each of your computers to the KVM switch,

using appropriate KVM & Audio/Mic cables.

LKV-S04ASK Configuration Diagram

Step 4. (Now your KVM Switch should have been powered-up….)

Power up the connected computers one by one. After

your computers are powered up, the keyboard and

mouse will be recognized and now you can begin

operating the KVM switch.

Easy Operation

There are two methods to control your KVM Switch for PC

switching: using the face-

panel push button or a hotkey

sequence. For audio/mic switching, use the hotkey command

See

Quick Reference Sheet

Face-panel buttons

The face-panel buttons allows you

a direct control over PC port

switching. Simply press the button to switch PC port. By default,

PC port switching and Audio/Mic port switching are bound

together (both will be switched simultaneously).

If you want to enable the binding of PC and audio/mic port

switching, use the hotkey sequence, ScrLk +ScrLk + Q. To

disable the binding again, just hit ScrLk +ScrLk + W.

See

Quick

Reference Sheet

Keyboard hotkey

A keyboard hotkey sequence consists of at least three specific

keystrokes:

See Quick Reference Sheet

Hotkey sequence = [ScrLk]

+ [ScrLk]

Command key(s)

* User-definable = SCROLL LOCK

, CAPS

, ESC

, F12

or NUM LOCK

Hotkey preceding sequence configuration:

For users who

want to use a preceding sequence other than two consecutive

Scroll Locks, there is also one conv

enient way to configure it:

Step 1.

Hit ScrollLock + ScrollLock + H, then two beeps will signal

readiness for new preceding sequence selection. [or Press and

hold down the last front-panel button (Button 2 or Button 4) until

you hear two beeps, and then release the button.]

Step 2.

Select and press the key you would like to use as your preceding

sequence (

SCROLL LOCK

, CAPS

ESC

F12

NUM LOCK

keys are available for selection) and you’ll hear a beep for

selection confirmation. Now you can use the new preceding

sequence to execute your hotkey commands.

Another way to activate the Hotkey preceding sequence

configuration is to press the last front-panel button (button 2/button 4)

for over 3 seconds to set the KVM switch into hotkey configuration mode.

Then you select and press the key that you’ll choose as the preceding

sequence.

Each keystroke within a hotkey sequence should be pressed within 2

seconds. Otherwise, the hotkey sequence will not be validated.

For detailed Hotkey sequences and their corresponding functional

commands, please refer to the Quick reference sheet.

1 2

Inhaltsverzeichnis

Seite 1 - Quick Installation Guide

Quick I nstallation G uide Applicable models: LKV-S02ASK

Seite 2 - Quick Reference Sheet

Quick Reference Sheet Applicable models: LKV-S02ASK / LKV-S04ASK Re

Verwandte Modelle: LKV-S04ASK

Kommentare zu diesen Handbüchern

Keine Kommentare

Linkskey LKV-S02ASK Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Computers Linkskey LKV-S02ASK herunter. Linkskey LKV-S02ASK User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: LKV-S04ASK

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Computers Linkskey LKV-S02ASK